Square TFT Display 4 Inch SPI&MCU 320x320 Dots Product Introduction
SAEF TECHNOLOGY SF-TO400DX-8979A-CT TFT LCD display module is a transmissive type color active matrix TFT(Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This module is composed of a TFT LCD module, a driver circuit, and a back-light unit. the resolution of a 4” contains 320 (RGB)X 320 dots, and it can display up to 262k color. SF-TO400DX-8979A-CT TFT LCD model supports MCU and SPI interface; the supply voltage (VCC) of driving LCD panel is from is 2.7V to 3.6V. Typical value is 3.3V.
SF-TO400DX-8979A-CT can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃. the LCD module is with PCAP capacitive touch screen, It is great for automation, GPS, medical equipment, industrial device, security equipment white goods, smart home applications, IoT System, car equipment, car dashboard, car audio, car clock, car door display system, water ionizer, which requires TFT display in high quality and colorful image.
Product Features:
| Product: | TFT 4″ Inch |
| Resolution: | 320X320 Pixels |
| Interface: | MCU SPI |
| Touch Screen: | With PCAP Capacitive Touch Screen |
| Outline Dimension: | 84.0(W) x 84.0 (H) x 3.37 (T) mm (with touch) |
| Viewing Direction: | All Viewing Angles (85/85/85/85) |
| Pin Number: | 40 Pins |
| Connection: | Plugging |
| Surface Luminance: | 300 Cd/m2 |
| Supply Power: | 3.3 V |
| Current Consumption: | 20 mA |
| Operating Temp.: | -20℃ To +70℃ |
| Life Time: | 40000 Hrs |
| Compliance: | REACH & RoHS Compliant |
Square TFT Display 4" SPI&MCU 320x320 Dots Product Drawing
Interface Pin Definition
| Pin No. | Symbol | Description | When not in use |
| 1 | LEDA | B/L positive pin | — |
| 2 | LEDK | B/L negative pin | — |
| 3 | LEDK | B/L negative pin | — |
| 4 | GND | Ground | — |
| 5 | VCI | Power supply(2.8-3.3V) | — |
| 6 | IOVCC | I/O power supply(1.8-3.3V) | — |
| 7 | TE | Tearing effect output | Open |
| 8 | CS | Chip selection pin. Low-active. | — |
| 9 | RS | Display data/command selection DCX=’ 1’ : display data or parameter. DCX=’0’ : register index / command. | — |
| 10 | WR/SCK | Write enable in MCU interface. In SPI mode, this pin is sclk | — |
| 11 | RD | Read enable | GND |
| 12 | SDI | SPI interface input/output pin. | — |
| 13 | SDO | SPI interface output pin. | — |
| 14 | GND | Ground | — |
| 15-30 | D0-D15 | Horizontal sync input | GND |
| 31 | RESET | This signal will reset the device and it must be applied to properly initialize the chip | — |
| 32 | IM2 | IM0=0 | IM2=0 | MCU 16 BIT | D[ 15:0] is used | — |
| IM0= 1 | IM2=0 | MCU 8 BIT | D[7:0] is used |
| 33 | IM0 | IM0= 1 | IM2= 1 | 4Line SPI | CS,RS,SCK.SDI | — |
| IM0=0 | IM2= 1 | Reserve | – |
| 34 | GND | Ground | — |
| 35 | TP_INT | TP Interrupt to the host | Open |
| 36 | TP_SDA | TP I2C data input and output | Open |
| 37 | TP_SCL | TP I2C clock input | Open |
| 38 | TP_RES | TP external reset, Low is active | Open |
| 39 | TP_VCI | TP power supply(2.8-3.3V) | Open |
| 40 | GND | Ground | — |
Backlight Electrical characteristics
| Item | Symbol | Min | Typical | Max. | Unit |
| LED module forward Voltage | VB LEDB | 12-13.2 | V |
| LED module current | IB LEDB | 30 | 40 | 50 | mA |
| LCM Surface brightness Luminance▼1 | LB SB | —– | 300 | —- | Cd/mP 2P |
| LCM Surface brightness uniform▼2 | LB DBBB | —- | 80 | —- | % |
LCD Electrical characteristics
| parameter | Symbol | Condition | Min | Typ | Max | Unit |
| Viewing Angle | Φ=3 O’clock | θ | Cr＞10 | 75 | 85 | | deg |
| Φ= 6 O’clock | 75 | 85 | |
| Φ=9 O’clock | 75 | 85 | |
| Φ=12 O’clock | 75 | 85 | |
| Contrast ratio | Cr | θ=0 Φ=0 | 800 | 1000 | | |
| Respone time | Tr+Tf | — | 25 | — | ms |
| NTSC | % | 55 | 60 | | |
| CIE(x,y) chromaticty | WHITE | X | θ=0 Φ=0 | Typ -0.03 | 0.294 | Typ +0.03 | |
| Y | 0.329 | |
Reliability Test
| NO. | ITEM | CONDITION | Cr |
| 1 | High Temperature Non-Operating Test | 70℃*48Hrs | *No Defect Of Operational Function In Room Temperature Are Allowable. *IDD of LCM in Pre-and Post-test Should Follow Specification |
| 2 | Low Temperature Non-Operating Test | -20℃*48Hrs |
| 3 | High Temperature/Humidity Non-Operating Test | 50℃*90%RH*48Hrs |
| 4 | High Temperature Operating Test | 60℃*48Hrs |
| 5 | Low Temperature Operating Test | -10℃*48Hrs |
| 6 | Thermal Shock Test | -10℃(30Min) -25℃(5Min) -60(30Min)*2 Cycles |
| 7 | ESD test | Voltage:±6KV R: 330Ω C:150pF Air discharge, 10time |
Square TFT Display 4" SPI&MCU 320x320 Dots Product Image 
Search keyword: tft 4", 4 tft lcd, 4" tft lcd, 4 inch tft lcd, tft lcd 4, 4 tft display, 4" tft display, 4 inch tft display, tft display 4 inch, tft display 4", 4 inch tft lcd display, 4" tft screen, 4 inch tft screen, tft screen 4 inch, tft screen 4", 4 inch tft lcd screen, 320x320 TFT, 4 inch IPS, 4 inch 320x320 dots, 4 inch mipi LCD,4 inch SPI mcu LC
Product Tags:
|
|
TFT LCD Manufacturer Supply Square TFT Display 4 Inch SPI&MCU 320x320 Dots Images
|
